2014/10/17

alambre de aluminio esmaltado magneto

alambre de aluminio esmaltado magneto para las ventas,
Gurantee 100% calidad, precio bajo, libre de muestras para realizar la prueba! enviarme correo electrónico:lp14@cnlpzz.com;skype:zzlpchina;

1.Diámetro:ronda:0.2mm-8.0mm
2.clase térmica:130,155,180,200,220C
3.Precio:precio de fábrica, el 100% del precio bajo
4.alta calidad,proporcionar sampls para realizar la prueba, de forma gratuita.
enviarme correo electrónico:lp14@cnlpzz.com;skype:zzlpchina;whats app:8615838308831

2014/10/14

How to solder enameled copper wire?

1.Set out all your parts to solder. Why we do this? Because the soldering iron is extremely hot, don't lay it down while you are looking for the next part to solder. You can buy a soldering kit, which includes a soldering gun and base, sponge and solder. Or you may already have some components such as the soldering iron. Put on all protective gear.

2.Plug in the soldering iron. Place the soldering iron in the stand. The soldering iron will take a few minutes to heat up. Only heat it up when you are ready to go. This prevents accidental burns or fires. Get your sponge wet and then wring out the water. The idea is to have a damp sponge, not one soaking in water.

3.Check the manufacture's instructions for the appropriate wattage for your specific electronics project. Electronic components require a certain amount of heat. Too much heat can melt the part you're trying to solder. Soldering irons come in different wattage outputs, so check for proper wattage rating.

4.Apply the tip of the soldering iron to the wet sponge to make the tip clean. Cleanliness is a must for good solder joints. Hold the soldering iron to the part you are soldering. Think of holding a pen or pencil. Avoid any contact with the tip or heat shield; both can reach 400 degrees in temperature.

5.Hold the solder to the joint you are trying to solder. Place the tip of the solder at the point where the solder iron tip and part you are soldering meet. Hold the solder in place for a few seconds until solder starts to flow. Remove the soldering iron before you apply too much heat. Inspect your joint. The joint should look like a dome and be shiny. It not, then apply a bit more solder to build up the joint. Don't forget to clean your soldering iron often on the wet sponge.
Established in 1993, has developed a professional manufacturer of Magnet Wires in China.

2014/09/28

郑州蓝普实业有限公司 ZhengZhou LP Industry Co, LTD



Zhengzhou LP Industry Co,ltd,welcome visit our website:http://www.lp-industry.com

Email:sales@cnlp.cc

Tel:+8615838308831

Whats App:+8615838308831

Skype:zzlpchina

2014/09/23

Q&A About Enameled Copper Wire

Q&A About Enameled Copper Wire


Q: What is Enameled copper wire?

A: Enameled copper wire is copper wire coated by a insulating paint usually colored red. 

Q: What is enameled copper wire?

A: yes, it's copper wire with a coating of enamel to insulate it. It's intended to be used in coils and transformers where the wire is wound with the turns in physical contact with each other. the 

enamel prevents the turns from shorting to each other. 

Q: The Properties of Enameled Copper Wire.

A: One of the primary properties that makes enameled copper wire desirable for these applications is the enameling insulation. Transformers, motors and generators .

Q: Enameled copper wire value?

A: Which of. Monetary value. Resistance. Density. Etc etc. 

Q: The UL Classification of Enameled Copper Wire.

A: Enameled copper wire is a type of magnet wire. This means it is used as the wire in electromagnets, which are magnets that use electricity to generate a magnetic field. The wire is wrapped in 

a tight coil. When an electric charge is applied, the wires generate the magnetic field. This type of wire has a wide variety of applications, including use in automobiles, motors and industrial 

machinery. It is also found in smaller devices and home appliances, such as computers, televisions and both cell and standard phones.


2014/09/21

FQA About Enameled Wire

FQA About Enameled Wire
Q: How to Do Enameling on Aluminum.
A: Enameling is the process whereby a fine layer of powdered glass is fused to a metal surface to provide a durable and often decorative covering. While the process dates back to the ancient Greeks, it has most recently been adopted and improved by the automotive industry, which has developed it into a commercial powder-coating application to produce a high-quality finish for car bodies and parts. Providing you have access to a kiln, you can learn how to enamel aluminum at home. The technique takes practice and experience to perfect, and you should initially practice on inexpensive aluminum objects.
Q: How to Enamel an Aluminum Hobbie.
A: After all the effort you put into your hobby project, the painting step is often the most important. This is the part of your project that people will see the most and a good paint job can make up for any previous mistakes. Painting on aluminum can be a little tricky. Good adhesion is the key and requires a mixture of both mechanical and chemical means to provide a long-lasting finish.
Q: What is wire enamel?
A: yes, it's copper wire or aluminum wire with a coating of enamel to insulate it.

Q: What is Enameled aluminum wire?
A: Enameled aluminum wire is aluminum wire coated by a insulating paint usually colored nuturer. The paint is polyester,polyester-imide,polyester over coated with polyamide and so on.
Q: What is enameled copper wire?
A: Enameled copper wire is copper wire coated by a insulating paint usually colored red. The paint is much thinpolyester,polyester-imide,polyester over coated with polyamide that other wires have, yet provide almost the same amount of insulation. Enameled wire is primarily used in the construction of electromagnets since it allows more loops to be packed into a smaller volume.

Any other questions,Please contact with us,we will give you answer ASAP.

Email:sales@cnlp.cc
      lpsales@cnlp.cc
TEL:+8637155625861
    +8615838308831
  

2014/09/10

About Enameled Aluminum Wire

About Enameled Aluminum Wiresuper enameled aluminum  wire factory iso9001About Enameled Aluminum Wire
our aluminum wire adopt advanced manufacture technique,have  advanced quality management , and with high efficiency.
1.certification number:
    UL certificated number:e345303
    SGS number:SHAEC1101538301
    SGS number:TJTC1005166/CHEM
    ISO number:15/11Q0267R00
    ISO number:15/11Q0266R00

3.Main Applications:
This kind of polyurethane enameled aluminum wire can be widely used in relays, transformers,micro-motor,air-conditioner,explosion-proof motor,dry-type transformer,anti-explosion motor,precision electric appliance ,electric motor,deflection coil,audio devices,buzzer,watch,microphone and so on.
4.Packing:
plastic spool,wooden spool and also can pack the goods according to the requirement of each client
5.Delivery time:
10days-30days
6.The special  advantage 
(1)high resistance to heat shock
(2)high temperature
(3)good performace at softening breakdown
(4)suitable for high-speed automated routing,
(5)able to be direct weld, with no pinhole,
(6)resistive to high frequency, wearing, refrigerants and electronics corona,
(7)high breakdown voltage, small dielectric loss angle ,
(8)dozens of times on pulse life as the ordinary compound enamel-insulated wire
ZhengZhou LP Industry Co.,Ltd.will provide users best product with the best service and best quality .Warmly welcome friends from all walks of lfe come to LP company to guide and negotiate business.

2014/01/14

The Professional Manufacturer Of Magnet Wire In China!

ZHENGZHOU LP INDUSTRY CO.,LTD





Established in 1993, has developed a professional manufacturer of Magnet Wires in China.
Products Scope:
our company produce various magnet wire, including Enameled Aluminum Wire, Enameled Flat Aluminum Wire, Enameled Copper Wire, Enameled Flat Copper Wire, Bare Aluminum Wire, Paper-Wrapped wire, NOMEX Paper Covered Wire, Fiber Glass Covered Wire and so on .
Factory Figures:
No. of Employees: 399, including 22 Senior Engineers Workshops: 27,000.00m2 in area included Oxygen-Free Copper and Aluminum Rod Workshop, Continuous Extrusion Workshop, Wire Drawing Workshop, etc.
Equipments:
76 Sets included Continuous Extrusion, Enameled Production Line, continuous enameled production line, polyester glass sintering line, package production line and sintered polyimide film production line. Production Capacity: 10,000.00MT/Year
Welcome to visit our factory and build a long-time business relationship with your esteemed company!